GUIDE

PHOTOSHOP: RETOUCHING

Natural retouching step by step: light, fixing flaws, skin, eyes and colour – so that the editing doesn't show.

THE PRINCIPLE

ALWAYS WORK ON LAYERS

Good retouching is non-destructive: each step goes on its own layer or adjustment layer, so you can later reduce, change or remove any correction. Name your layers (e.g. "Fixes", "Skin", "Eyes") and save the work in PSD format.

  • Order: 1. basic corrections in Camera Raw or Lightroom → 2. removing flaws → 3. skin → 4. eyes and details → 5. colour → 6. sharpening last.
SECTION 1 • LIGHT & CONTRAST

1. LIGHT AND CONTRAST (CURVES)

Create a Curves adjustment layer from the bottom of the Layers panel to control the light without losing quality:

  • S-curve: Raise the top (light tones) and lower the bottom (dark tones) to add contrast.
  • Targeted adjustment: Choose the hand icon in the Curves panel (Targeted Adjustment Tool) and drag up or down directly on the photo. Photoshop adjusts exactly the tonal range under the mouse.
  • Only part of the photo: Every adjustment layer comes with a mask. Paint black on the mask over the areas the adjustment must not affect.
SECTION 2 • FIXING FLAWS

2. FIXING FLAWS

Always create a new empty layer and turn on "Sample All Layers" in the top bar.

Spot Healing Brush (J) Fixes spots, dust particles and small specks when you paint over them. Photoshop blends the fix into the surroundings automatically.
Remove Tool (J) An AI-based removal tool in the same group. Paint over a larger object, such as a power line or a passer-by. It often works better than the traditional tools.
Clone Stamp (S) Set the source point by holding Alt and clicking. Paint over the spot to hide it. Best for precise edges, such as a horizon or the corner of a building, where the other tools make a mess.
Content-Aware Fill Select the object with the lasso and choose Edit > Content-Aware Fill. Good for large areas and for situations where you want to decide yourself where Photoshop takes the fill from.
SECTION • SKIN & EYES

NATURAL SKIN AND LIVELY EYES

  • Remove only what is temporary: Spots and scratches can go, but moles, scars and wrinkles belong to the person. Ask the person you photographed if in doubt.
  • Softening shadows (dodge & burn): Create a new layer, fill it with 50 % grey and change the blend mode to Soft Light. Paint with a soft brush at low opacity (5–10 %): white to lighten and black to darken. This evens out under-eye shadows and unevenness without destroying the skin texture.
  • Eyes: Brighten the iris slightly with a Curves adjustment layer and a mask. Don't whiten the whites of the eyes to pure white – it immediately looks unnatural.
  • Check: Hide the retouching layers now and then with the eye icon and compare with the original. If the difference jumps out, lower the opacity of the layers.
SECTION 3 • SELECTION & MASK

3. CUTTING OUT A SUBJECT

Click Select Subject in the top bar for an automatic selection. Use the Select and Mask workspace and the Refine Edge Brush for hair. Save it as a layer mask.

SECTION 4 • COLOUR

4. MAKING COLOURS CONSISTENT

Add a Color Lookup adjustment layer on top. Choose a look that suits your photo from the 3D LUT list and set the opacity to about 20–40 %.

TROUBLESHOOTING

RETOUCHING PITFALLS

Skin looks plastic? Overusing the brush destroys the texture. Use a small brush and fix only the obvious flaws.
Clone Stamp makes a mess? Use a soft brush (hardness 0–30 %) on smooth surfaces and a harder one on edges. Change the sample point (Alt-click) often so that no repeating pattern appears.
An adjustment ruins the whole photo? Limit the adjustment to the layer directly below it by making a clipping mask with Ctrl + Alt + G.

All guides · Ask about this guide